//fldigi macro definition file extended // This file defines the macro structure(s) for the digital modem program, fldigi // It also serves as a basis for any macros that are written by the user // // The top line of this file should always be the first line in every macro // definition file (.mdf) for the fldigi program to recognize it as such. // // // Macro # 1 /$ 0 Clear RX // // Macro # 2 /$ 1 Clear TX // // Macro # 3 /$ 2 Call Resend @>| \n , Resend your last message, de - - K\n // // Macro # 4 /$ 3 Go Ahead @>| \n , Go ahead, de - - K\n // // Macro # 5 /$ 4 Standby @>| \n , Standby, de - - K\n // // Macro # 6 /$ 5 You're Welcome @>| \n You're Welcome, de - - K\n // // Macro # 7 /$ 6 Thank you @>| \n Thank you, de - - K\n // // Macro # 8 /$ 7 Rtn To Voice @>| \n Returning to voice net, de - - K\n // // Macro # 9 /$ 8 T/R @>| \n // // Macro # 10 /$ 9 Tx @>> \n // // Macro # 11 /$ 10 Rx @|| \n // // Macro # 12 /$ 11 TX MYCALL @>| \n de - - K\n // // Macro # 13 /$ 12 CI with Traffic @>| \n de - msg(s) Power: W - - K\n // // Macro # 14 /$ 13 CI w/o Traffic @>| \n de Power: W - - K\n // // Macro # 15 /$ 14 Relay Checkin @>| \n Relay Checkin of , de - - K\n // // Macro # 16 /$ 15 User Defined Macro \n User Defined Macro\n // // Macro # 17 /$ 16 Rdy to Copy? @>| \n , are you ready to copy? de - - K\n // // Macro # 18 /$ 17 Ready to copy! @>| \n ready to copy! de - - K\n // // Macro # 19 /$ 18 Operator Checklist Configuration Minimums Operators:\n \n 1). Operator Section - all sections, Antenna: optional\n \n 2). UI/Macros\n Enable Two Scheme 8\n Enable "Load last used macro file on startup"\n Enable "Display macro filename on startup"\n Enable "Prompt to save macro file"\n \n 3). Modems/MT-63\n Enable\n 8-bit extended characters,\n Long receive integration,\n 1 second Tone Duration\n Manual tuning\n \n 4). Soundcard/Devices\n Enable PortAudio\n Select Capture device\n Select Playback device\n Disable Device supports full duplex\n Be sure soundcard is calibrated (CheckSR.EXE or WWV)\n \n 5). ID/RsID\n Enable\n "Medium" Allow Errors \n Pre-Signal Tone = "4.0" seconds\n Enable tx freq lock\n Squelch open (sec) = "0"\n \n 6). Set SIG levels so that in TUNE the signal just fits\n between the two gray lines\n \n 7). Before the net begins all operators should fill:\n The "In" box with 0 or the number of messages they\n wish to send.\n The "Out" box with their transmitted power level.\n \n Note:\n These macros can be found at:\n www.k1hil.org\n \n // // Macro # 20 /$ 19 Operator Settings // // Macro # 21 /$ 20 Reserved // // Macro # 22 /$ 21 Reserved // // Macro # 23 /$ 22 Rtn To NCS @>| \n Returning to Net Control, de - - K\n // // Macro # 24 /$ 23 TX MY CS/QTH @>| \n de , - - K\n // // Macro # 25 /$ 24 NCS Checklist Configuration Minimums for Net Contol Operators:\n \n 1). Operator Section - all sections, Antenna: optional\n \n 2). UI/Macros\n Enable Two Scheme 8\n Enable "Load last used macro file on startup"\n Enable "Display macro filename on startup"\n Enable "Prompt to save macro file"\n \n 3). Modems/MT-63\n Enable\n 8-bit extended characters,\n Long receive integration,\n 1 second Tone Duration\n Manual tuning\n \n 4). Soundcard/Devices\n Enable Port Audio\n Select Capture Device\n Select Playback Device\n Disable Device supports full duplex\n Be sure soundcard is calibrated (CheckSR.EXE or WWV)\n \n 5). ID/RsID\n Enable\n "Medium" Allow Errors \n Pre-Signal Tone = "4.0" seconds\n Enable tx freq lock\n Squelch open = "0"\n \n 6). Set SIG levels so that in TUNE the signal just fits\n between the two gray lines\n \n 7). Before the net begins all Net Control Operators should fill:\n The "In" box with 0.\n The "Out" box with their transmitted power level.\n The "Call" with the call of the ANCS.\n \n 8). When acknowleging a checkin the NCS must fill the "In"\n box with 0 or the number of messages sent by the\n checkin. \n \n Note:\n These macros can be found at:\n www.k1hil.org\n \n // // Macro # 26 /$ 25 NCS Settings // // Macro # 27 /$ 26 Reserved \n // // Macro # 28 /$ 27 Reserved // // Macro # 29 /$ 28 BPSK-125 // // Macro # 30 /$ 29 Reserved // // Macro # 31 /$ 30 MT63-2KL // // Macro # 32 /$ 31 Reserved // // Macro # 33 /$ 32 Tune 10 secs @>| \n de - - K\n // // Macro # 34 /$ 33 Dec CNTR = 4 // // Macro # 35 /$ 34 Init CNTR = 5 \n // // Macro # 36 /$ 35 DTN in CNTR mins \n Digital Training Net will start in minutes.\n \n All stations standby... de , - - K \n // // Macro # 37 /$ 36 NCS Startup @>| \n \n \n \n Calling the Hillsborough County ARES Digital Training Net.\n Calling the Hillsborough County ARES Digital Training Net.\n \n de \n NCS for the Hillsborough County ARES Digital Training Net.\n \n is the Alternate NCS (ANCS) for this net.\n \n V09E13.mdf is the Macro file used by NCS\n Watts is the NCS power Level\n \n This is a directed net and all stations should follow standard net procedures.\n Please standby until your area is called.\n \n Stations with traffic send call sign, area, (# of messages), and power level\n \n Example: de 1 msg(s) - Power: 30 W - 1843L - K\n \n Note: the "CI with traffic" macro (on macro line #2) will do this for you automatically\n Remember to fill in the "In" box for the number of messages.\n Remember to fill in the "Out" box with your power level.\n ***\n \n Stations without traffic send call sign and area, and power level\n \n Example: de - Power: 30 W - 1843L- K\n \n Note: the "CI w/o traffic" macro (on macro line #2) will do this for you automatically\n Remember to fill in the "Out" box with your power level.\n \n ***\n \n de K\n \n \n \n de \n NCS for the Hillsborough County ARES Digital Training Net.\n \n Check-ins will be asked for in the following order:\n \n Nashua/Merrimack\n Manchester/Goffstown/Bedford\n Hollis/Brookline/Amherst/Milford/Hudson\n all_other\n \n Relays will be asked for after formal Check-ins\n \n To confirm receipt of traffic use call signs only.\n \n Note: the "TX MYCALL" macro (on macro line #1) will do this for you automatically\n // // Macro # 38 /$ 37 Nothing Heard @>| \n Nothing heard. Continuing.... de - - K\n // // Macro # 39 /$ 38 QTH Check-In @>| \n stations check-in now...\n // // Macro # 40 /$ 39 NCS ACK CALL @>| \n NCS acknowledges , with msg(s).\n de - - K\n // // Macro # 41 /$ 40 Alternate ANCS? @>| \n Would someone like to be the alternate NCS for this net? Call signs please. de - - K\n // // Macro # 42 /$ 41 Any Business@>| \n Any further business for the net? Call Signs Please. de - - K\n // // Macro # 43 /$ 42 Any Relays? @>| \n Any Relays for Stations not acknowledged by NCS? de - - K\n // // Macro # 44 /$ 43 NCS Shutdown @>| \n This has been another session of the Hillsborough County ARES Digital Training net.\n \n I would like to thank all the stations that participated.\n \n 73 to all de \n \n - K\n // // Macro # 45 /$ 44 Reserved // // Macro # 46 /$ 45 CALL Send Msg @>| \n , send your msg(s) to the net, de - - K\n // // Macro # 47 /$ 46 ANCS on Freq? @>| \n Is on Frequency? Call sign Please\n de - - K\n // // Macro # 48 /$ 47 NCS TX@>| \n de , NCS for the Hillsborough County ARES Digital Training Net - \n